文章
  • 文章
搜索
首页 >> 团购 >>PET类产品 >> 50um单层亚克力托底排废膜
详细说明

50um单层亚克力托底排废膜

价格
¥1.45
累计销量0累计评价0
城市
东莞
供货数量
1000000
最小定量
10000
购买数量
- +
总计¥14500
联络电话
18589099848
收藏
产品编号 M-TE5002TA
  • 产品说明
  • 产品参数
  • 所有评价

image.png                                                                                             

         

物理参数Physical parameters


项目(project)

单位(unit

  测试值(test   value








基材厚度

Substrate thickness

mm

0.045

± 0.002









胶厚

Glue thickness

mm

0.005

± 0.002









总厚度

aggregate thickness

mm

0.050

± 0.002















粘着力(adhesive force

    g/25mm                      

3-6

g








 

测试条件(180°剥离力测试)  Test conditions (180 ° peel strength test)

   测试标准testing standard):GB/T2792-1998;

   测试样品宽度Test sample width):25mm;

 测试被贴物Test the paste): SUS304 钢板(SUS304 steel plate)

  测试环境Test environment):温度temperature 23±2℃;相对湿度relative humidity 55%±5%

 测试速度Test speed):300mm/min;

   制备试样前,试样卷(片)、试板应在温度为23±2℃,相对湿度为55%±5%条件下放置2h以上。

(In pieces before the preparation of sample, sample volume (piece), the test plate shall be at a temperature of 23 + 2 , relative humidity of 55% plus or minus 5% is placed under the condition of more than 2 h.)


使用说明 (instructions)‹

u  被贴物表面状况可能影响保护膜贴合效果,使用前请将被贴物表面油污、水分、灰尘等杂质清理干净;

(posted material surface condition may affect the effect of coating and laminating, posted surfaces prior to application oil, moisture, dust and other impurities clean;)

u  多种溶剂和水份会引起保护膜残留,如被贴物有经溶剂擦拭或印刷等工艺,请经过充分干燥后再贴合保护膜;

(variety of solvent and water can cause protective film residue, such as being posted by solvent to wipe or printing craft, please fit again after fully dry protective film;)

u  由于环境温度、湿度会对保护膜剥离力产生较大影响,如要获得稳定的剥离力,请将保护膜与被贴物在23±2℃,相对湿度为55%±5%条件下放置2h以上再使用;

due to environment temperature and humidity will have great influence on the protective film stripping force, as to the stability of the stripping force, please put the protective film and posted content in 23 ± 2 , relative humidity of 55% plus or minus 5% placed more than 2 h again under the condition of use;

  产品的胶层属于对压力敏感的胶黏剂,所以在贴合时须给予充分压贴;

The adhesive layer of the product belongs to the adhesive which is sensitive to pressure, so it should be fully pressed when fitting.

  保护膜在贴合好20分钟内对被贴物剥离力会有一个少量爬升的现象,20分钟后剥离力趋于稳定;

protective film to be posted in joint good 20 minutes there will be a small climb the phenomenon of the stripping force, stripping force to stabilize after twenty minutes;

在产品胶层完整性被破坏以后,使用时有可能会产生残留现象,所以请根据使用工艺进行充分研究;

sub integrity after the destruction of the products, use which may produce residual phenomenon, so please according to use technology to fully research;

u  保护膜残留形成机理有多种,如出现残留现象请描述详尽工艺和现象,以便我们针对不同原因采取有效措施.

residual formation mechanism has a variety of protective film, such as residual phenomenon occurring, please describe the detailed process and phenomena, so that we can take effective measures for different reasons.

储存条件及有效期Storage conditions and validity period.

u  产品最佳储存条件:避免阳光直射,温度10-30℃,湿度小于70%;

products the best storage conditions: avoid direct sunlight, temperature 10 to 30 , humidity is less than 70%;

   在生产日期后6个月内使用产品,可获得最好的使用性能。对日光直射、高温(40℃以上)、高湿(70%RH 以上)、低温(0℃以下)等条件下不作6个月保证。

The product can be used within 6 months after the production date, and the best performance can be obtained. To direct sunlight, high temperature (over 40 ), high humidity (70% RH), such as low temperature (below 0 ) under the condition of not for 6 months.

注意事项matters need attention

* 以上产品资料数据,仅供参考之用。

The above product data is for reference only.

*使用本产品时,请事先对产品用途(目的、条件)适合与否进行充分研究。

When using this product, please make full research on the suitability of the product (purpose, condition) in advance.

*不同材质的表面及不同的贴合条件,有可能造成起反应、残留等异常现象,所以在使用前请先进行充分试验。

The surface of different materials and different fitting conditions may cause abnormal phenomena such as reaction and residual, so please make full test before use.)                                 


与描述相符
0

  • 非常不满
  • 不满意
  • 一般
  • 满意
  • 非常满意
×